How To Reset Nordictrack Treadmill: 13 different brands of treadmills

This is a complete guide on How To Reset Nordictrack Treadmill, I will show you all the possible ways to restart not only Nordictrack treadmills, but also treadmills from 13 different manufacturers.

Let’s get started


How to restart treadmills

If the electronics on your running machine do not work properly or if you have performed maintenance on your machine, you may need to reset it.

Restarting a treadmill is a relatively quick process. Simply press the reset button on the treadmill and then a few buttons on the console.

Depending on the type of treadmill you have, there are three possible ways to reset it.


back to menu ↑

Initial procedures for all treadmills

how to reset nordictrack treadmill

Step 1

Unplug the machine from the outlet and insert the safety key into the safety key slot.

Step 2

Find the reset hole at the bottom of the console. Now reconnect the switch’s treadmill and insert a swab or piece of plastic into the reset hole and press reset.

Step 3

If you can see the CL11 appear on your dashboard or console, continue with the Treadmills with the current software.

If nothing appears on the console, go to Treadmills with LCD screen and old software, as long as your treadmill has an LCD screen or Treadmills with Old Software and LED Display if it has an LED display.

Consult your user’s manual if you are not sure what type of display you have.


back to menu ↑

How to Reset NordicTrack Treadmill

how to reset nordictrack treadmill

NordicTrack reset method 1:

  • Make sure the machine is not moving or running any programs.
  • Locate the hole/reset button under the console.
  • Similar to press the button or use a swab if this is required.
  • When finished, the running machine will perform the reset.

NordicTrack reset method 2:

We have other models of NordicTrack treadmills in which the reset button is located in front of the treadmill next to the power code.

If you have a reset button triggered, first make sure you have not plugged your treadmill into a GFCI outlet.

Second, wait for about 5 minutes and then press it again to restart the system.

Unfortunately, the NordicTrack treadmill does not support GFCI output, so it has a warning in its manual that it could cause frequent reboot problems.

NordicTrack reset method 3:

  • To reset the NordicTrack treadmill, the first thing you will do is set the switch to OFF.
  • Then wait 5 minutes and then turn the switch to ON.
  • To stop the machine from running, press the Stop button, the time starts to arrive on the screen.
  • To reset the cloth to run, press the Start button or to increase the speed.

back to menu ↑

How to Restart Treadmills With Current Software

Step 1

Press the reset button again and verify that “CL 21” appears on your dashboard or console.

Step 2

For our second step, you will first press the Enter button 5 times on your console, until the screen displays “CL 26”.

Step 3

Press “Enter” once more so that “E” appears.

Step 4

Press “Enter” and after “SS” is displayed, press the “Start / Stop” button.

Step 5

Press “Enter” and let the running machine run until it stops by itself.

Step 6

Press the POWER button 2 times.


back to menu ↑

How to Restart Treadmills With Old Software and LCD Screen

Step 1

Unplug the treadmill for about 30 seconds so that it does not work.

Step 2

Remove the safety key and reconnect the machine to run.

Step 3

Once the 10 has appeared on the screen you must press the “Reset” button.

Step 4

For this fourth step you will have to press the ENTER button 5 times, then 1 time to STAR, and finally ENTER once more.

Step 5

Replace the security key and press “Enter”.

Step 6

Press the “Power” button 3 times.


back to menu ↑

How to Restart Treadmills With Old Software and LED Display

Step 1

Unplug the machine to run for at least 30 seconds.

Step 2

Remove the safety key and reconnect the machine to run.

Step 3

Once the 10 has appeared on the screen you must press the “Reset” button.

Step 4

Press the ENTER key 4 times, then SART 1 time, and then ENTER again.

Step 5

Replace the security key.

Step 6

Now all you have to do is turn on your treadmill and wait 8 minutes for the machine to restart.; the treadmill will run on its own during this time.

Step 7

Press the “Power” button 3 times.


back to menu ↑

Resetting the treadmill according to the brand

Bowflex

This is for the 3, 5 and 7 series of treadmills.

Press and hold the ENTER and POWER keys for 3 seconds. This puts the treadmill in idle mode.

From here you can access many functions, please refer to your user manual for each one and how to access them.

For the BXT series, turn the machine on to run and it will enter the power mode.

While in this mode, you must hold down the stop or pause button and the decrease button for three seconds to access the treadmill settings.

You can make several choices from here by pressing down or up. A reset console is one of the options. Activate it by pressing enter when it is highlighted.

For Treadclimbers, turn the machine on to enter power mode. In the mode, you have to press and hold the Pause/Stop Button and the Right Button for 3 seconds.

As with the BXT series, you are now in the machine setup. From here, you choose the option to restart the console and press enter.

Cybex

  • The on/off switch on the front of the engine cover.
  • Turning it on will put it in idle mode.
  • Pressing “Clear 750” on the keypad allows you to enter the settings menu.
  • Always contact customer service if you have any problems.

Freemotion

  • First, enter the setup mode by accessing the start menu.
  • Touch the “i” button near the lower-left corner of the screen.
  • From here, you must enter the maintenance mode by pressing the maintenance button in the lower-left corner again.
  • You then have all kinds of functions you can perform, including factory defaults, by pressing the selection where it is displayed.

Horizon Fitness

  • The first thing you will do is make sure that nothing on the treadmill is running by pressing the pause or stop button.
  • When everything has finished, press and hold the pause or stop button for 3 seconds and this will reset your treadmill.

Life Fitness

On many models, there is a reset button. On most, there is a diagnostic function that requires a few different codes for each model.

The diagnostic treadmill code and model can be found on the Life Fitness website, where you can see all the treadmill models that differ from this one.

How To Reset Nordictrack Treadmill: 13 different brands of treadmills

Matrix

  • There are two stages to make a reset. For a normal reset, press and hold the PAUSE button for 3 seconds.
  • Then there is the administrator’s setting from which you have the most access to the different preset options within the treadmill.
  • Press and hold ELEVATION DOWN and SPEED UP for 3 seconds.
  • The down and up buttons will help you get to the different settings of the machine more easily.

Nautilus

  • There is a built-in diagnostic system that you can access by pressing speed: UP, 6, ENTER.
  • When in this mode, you can test various components and parts of the treadmill.
  • Check your manual to see which ones you can access and how to start them.
  • When you are finished with the diagnostics press the CLEAR key.

Precor

  • There is an on/off switch under the hood near the power cord.
  • You must make sure that your treadmill is reset and that everything is stopped, as it will last 30 seconds off and then on again.
  • Some models of that brand of treadmill do not have a reset button but others do.
  • If you press restart, 5, 6, 5, 1, 5, 6, 5, you can enter the programming mode of this treadmill, which I am sure many will need.

Proform

  • They are manufactured by the same company and have software and components similar to the previous NordicTrack treadmills.
  • Therefore, make sure that the machine is not in a program or in motion.
  • Locate the hole/reset button under the console.
  • This will require a swab or similar to press the button.
  • When finished, the machine will run the reset.

Sole Fitness

  • The first thing you will do is make sure that nothing on the treadmill is running by pressing the pause or stop button.
  • When everything has finished, press and hold the pause or stop button for 3 seconds and this will reset your treadmill.

Woodway

  • Woodway Curve has a reset button on the console at the bottom right.
  • Press to reset all other readings and then press again during the zero-mode diamond setting.

Xterra Fitness

  • Make sure everything is standing still and not moving.
  • Press stop and hold for 3 seconds, then a reset will occur.

Never stand on the belt of your running machine while restarting it. Resetting causes the belt to start and stop automatically, which can lead to injury.

Related Article:

30 Minute Beginner Treadmill Workout – Perfect Beginners

How to Reduce Treadmill Noise in an Apartment – 3 Ways

How To Use a Treadmill: Complete Beginner’s Guide

We will be happy to hear your thoughts

      Leave a reply

      Mr Lazaru
      Enable registration in settings - general
      Compare items
      • Total (0)
      Compare
      0